Strona 1 z 1

[DIY] DRSSTC Italy!

: 17 cze 2013, 17:12
autor: joeb
naruszać

Nazywam się Joe, piszę z Włoch. Ja jestem za pomocą tłumacza, bo nie mówię po polski. Mam nadzieję, że rozumiesz.

I like your forum, znalazłem wiele zdjęć tesla DRSSTC i bardzo ciekawe dyskusje!

Chciałem pokazać mój projekt.

Właśnie zacząłem, mam nadzieję, że do końca to i to działa dobrze.

Mam nadzieję, że będzie można.

http://imageshack.us/a/img189/964/dsc0823l.jpg
Steve Ward U.D 2.5 (Eric Rev.)
http://imageshack.us/a/img402/1153/dsc0824ag.jpg
Interrupter NE555
http://imageshack.us/a/img837/6461/dsc0825me.jpg
Semitrans SKM300GB12T4 and 403GB128D
http://imageshack.us/a/img835/7008/dsc0827lc.jpg
Cap
http://imageshack.us/a/img443/1425/f8m5.jpg
Test!!
http://imageshack.us/a/img39/3766/tctv.jpg
http://imageshack.us/a/img543/50/3xrf.jpg
http://imageshack.us/a/img62/156/1cjf.jpg

teraz muszę zbudować pierwotnego i wtórnego cewki.

Chciałbym zatrzymać się na około 40kHz.

mogę napisać więcej szczegółów później!

Dziękuję wszystkim.

Joe

Re: [DIY] DRSSTC Italy!

: 17 cze 2013, 18:39
autor: Yuri
Can You write this message in english? We are able to translate english into understable polish better than translator.

Re: [DIY] DRSSTC Italy!

: 17 cze 2013, 18:48
autor: admin
Witaj na myHV, joeb!

@Yuri: Akurat tłumaczenie włoski>polski jest niezłe ; )

@joeb: Czekamy na więcej szczegółów.

After some back and forth translations I think it will be better if we write in english.

Re: [DIY] DRSSTC Italy!

: 17 cze 2013, 18:50
autor: Yuri
@hvman: Faktycznie, źle nie jest, jednakże pragnę zmontować z tego czystą polszczyznę. :D

Re: [DIY] DRSSTC Italy!

: 18 cze 2013, 06:45
autor: Mania-C
Is great to see people from other country on a forum.
translation is all most fine, but if you can simple writhe in English
Good luck and We waiting for more news :D

Re: [DIY] DRSSTC Italy!

: 18 cze 2013, 09:08
autor: joeb
thanks all for replies! is more simple for me write in english! :D

this project it's just at the beginning, so i'm going around for find all the parts i need!!

yesterday a found the wire for secondary.


i planning to use 250mm Diameter and 1000mm Eight using 0,45mm (25AWG) wire. My software say:

- 70,90khz of resonant f.
- 42,97khz of quarter wavelength
- 31,78pF Toroid capacitance required

i hope is a good choise for my project!

but, i'm working parallelamente with a Rotary spark gap TC, almost ready! i think is better to open another post for details! ;)

Joe

Re: [DIY] DRSSTC Italy!

: 18 cze 2013, 21:00
autor: Mania-C
Do you use a pulse train modulation to convert a high state interruptor through toslink ?
I think that this is the only way out of the problem because the receiver in their internal structure have AGC (Automatic Gain Control).

Re: [DIY] DRSSTC Italy!

: 19 cze 2013, 09:56
autor: joeb
Actually.....i don't know this kind of control! i use the Toslink (Sharp 5Volt type) like a simple opto-transmitter and reciever!......and its work great!!

In the Interrupter side, the direct output of 555 IC is directly connected to Input PIN of Transmitter with a 1K resistor, and in the Driver Side the signal from reciever is directly passed through a Smith Trigger! it's all!

The interrupter sch is taken from here Steve Ward Interrupter

and the Driver U.D.2.5 From here Eric Goodchild

and you? what kind of Driver uses? i saw a particular driver used in this forum, have you some kind of schematics?

Re: [DIY] DRSSTC Italy!

: 9 lip 2013, 22:01
autor: Dżejwor
People in poland usually use hammertone predikter. I think it is much better option than Ward's UD 2.x drivers. But much more expensive and dificult to tune. Simple NE555 Ward's interrupter is a bad thing - available range of adjustment easy can blow up whole coil. Absolutely not to be exceeded: 1kHz PRF and ~10% duty cycle. Toslink is not a good option - that receivers are sensitive to electromagnetic lnterference it easy can generate too long pulses and other bad things at its output.

Re: [DIY] DRSSTC Italy!

: 13 lip 2013, 15:27
autor: joeb
Dzejwor, uhm.....now you put on me some doubts! For this tesla, i think i'll use Ward's driver....but for the next one i want to try this Hammertone!.... what kind of more accurate interrupt you can suggest me? The version i create have 2khz output with 5% duty!

i'm here for have suggestion and critics, so i'm happy for your reply!

Re: [DIY] DRSSTC Italy!

: 26 lip 2013, 11:39
autor: joeb
Found another, more accurate interupter from Steve Conner.

Steve Conner's Interrupter



and in this website......a modified Toslink reciever for noise-less!

Toslink MOD

Re: [DIY] DRSSTC Italy!

: 11 mar 2014, 00:09
autor: joeb
Hi!

Can anyone say me were i can find the schematic and documentation about Predikter driver?

Thanks!

Joe

Re: [DIY] DRSSTC Italy!

: 11 mar 2014, 07:31
autor: slu_1982

Re: [DIY] DRSSTC Italy!

: 11 mar 2014, 19:23
autor: joeb
Thanks slu! But......for have some documentation or BOM list?

Re: [DIY] DRSSTC Italy!

: 11 mar 2014, 21:46
autor: slu_1982
Part list, idea circuit, multilayer with elements, photo of bottom elements, eagle projects
predi.rar
(2.33 MiB) Pobrany 631 razy

Re: [DIY] DRSSTC Italy!

: 11 mar 2014, 22:00
autor: joeb
Thanks Slu! i'm studying this driver and valuating the idea of realization. i want to test both driver, Ward and Predik.

Why there isn't a website or a post with all the documentation and explanation? Seems to be a very good project and a lot of coilers can like and decide to use it!

Thanks
Joe!